Titanium Grade Cross-Reference Chart
Grade names come from whichever standard the drawing was written to. This chart lines ASTM/UNS, EN/ISO, GB and the Russian GOST names up side by side — and flags where a “same grade” label hides a real chemical difference.
Wrought titanium: ASTM vs EN vs GB vs GOST
| ASTM / UNS | EN / ISO numeric | GB (approx.) | GOST RU (approx.) | Condition | Typical use |
|---|---|---|---|---|---|
| Gr1 · R50250 | Grade 1 · 3.7035 | TA1 | ВТ1-0 | Annealed | Chemical tank lining, low-stress formable parts |
| Gr2 · R50400 | Grade 2 · 3.7065 | TA2 | ВТ1-0 | Annealed | The workhorse: plate, tube, fittings, marine hardware |
| Gr3 · R50550 | Grade 3 · 3.7075 | TA3 | — | Annealed | Rare; intermediates get specified then substituted |
| Gr4 · R50600 | Grade 4 · 3.7095 | TA4 | — | Annealed | Higher-strength CP, heat-exchanger plate |
| Gr5 · R56400 | Grade 5 · 3.7165 | TC4 | ВТ6 | Annealed / STA | Aerospace fitting, high-strength machined parts |
| Gr7 · R52400 | Grade 7 · 3.7240 | — | — | Annealed | CP + palladium for reducing-acid service |
| Gr9 · R56320 | Grade 9 · 3.7025 | TC3 | — | Annealed | Hydraulic tube, moderate strength with weldability |
| Gr11 · R52600 | Grade 11 · 3.7115 | — | — | Annealed | CP + Pd, welded chemical fabrication |
| Gr12 · R53400 | Grade 12 · 3.7055 | — | — | Annealed | CP + Mo/Ru, elevated-temperature strength |
| Gr23 · R56401 | Grade 23 ELI · 3.7165 ELI | TC4 ELI | ВТ6-0 (ELI-type) | Annealed / STA | Implant, cryogenic, fatigue-critical service |
Cast titanium (for completeness)
| ASTM B367 | EN / ISO | Note |
|---|---|---|
| Ti Gr1 / Gr2 C | 3.7065 cast equivalents | Cast CP for pump bodies and valve housings |
| Ti Al6V4 C (Gr5 C) | 3.7165 cast | The common investment-cast structural alloy |
| Ti Al6Sn4Zr2Mo C | Ti-6242 family | Higher temperature capability; verify before substituting |
The five substitution traps
- Interstitial bands differ. Gr2 and Grade 2 (3.7065) sit in the same strength family, but the oxygen and iron ceilings are set by different documents. For a weldment with a specified minimum, verify against the standard named on the drawing, not the grade label.
- Gr5 and Grade 5 (3.7165) are close but not identical on the aluminium/vanadium window. The practical risk is in fatigue-rated parts, where the supplier must show which document they actually tested to.
- ELI matters when it is written. Grade 23 / 3.7165 ELI carries tighter interstitial limits for implant and cryogenic use. Substituting Gr5 for Gr23 because the strength looks the same is how fatigue cracks start. Details on the Gr5 vs Gr23 page.
- GB designations are not one-to-one. TA1/TA2 map to the CP family and TC4 to Ti-6Al-4V in common usage, but the Chinese chemical windows are their own document. If your paperwork accepts GB, we supply GB; if it demands ASTM, we supply ASTM.
- GOST names are market habit, not a spec sheet. Russian-speaking buyers order ВТ1-0 for CP titanium and ВТ6 for Ti-6Al-4V, but GOST chemistry and ASTM limits are separate documents — and ВТ1-0 spans what ASTM splits into Gr2/Gr3/Gr4. Treat the GOST name as intent, then pin the acceptance standard on the PO. Our Russian-language ВТ6 supply page covers the route.
What we ask on an RFQ that names two standards
Which document governs acceptance. That single decision sets the mill route, the test frequency and the price. Grade names are a shortcut for humans; standards are what a weld inspection and a pressure test are actually checked against.
Frequent questions
FAQ
Is Grade 2 the same as TA2?
In daily trade, yes — both are the workhorse commercially pure grade. Formally they are governed by different chemical windows, so a contract that names ASTM B265 Gr2 should be supplied and certified against ASTM B265, not GB.
Can I swap Gr5 for Gr23 to save money?
Only if the part is not fatigue- or fracture-critical. Gr23 ELI holds tighter interstitial limits, which is exactly why it is specified for implants and cryogenic work. Where the drawing says ELI, buy ELI.
Which standard should my drawing cite?
Whatever your customer inspection accepts. We supply to ASTM, EN, GB or your in-house spec; the standard drives mill selection and test frequency, so pinning it early removes a whole class of quotation ambiguity.
Do you stock all these grades?
Gr1, Gr2, Gr4, Gr5, Gr9 and Gr23 are routine. Gr7, Gr11 and Gr12 are campaign orders with longer lead times — ask us before designing around them.