Titanium Weight Calculator
Type nominal dimensions in millimetres — the mass updates as you type. Built for freight budgeting, nesting checks, and sanity-checking a supplier's weight sheet before you commit to a quote.
The maths behind it
| Material | Designation | g/cm3 | Why this figure |
|---|---|---|---|
| Commercially pure Ti | Gr1 / Gr2 / Gr4 · UNS R50250–R50550 | 4.51 | CP titanium spans 4.43–4.55 by interstitial content; 4.51 is the published convention for Gr2. |
| Ti-6Al-4V | Gr5 · UNS R56400 | 4.43 | Aluminium in the alloy pulls density below the CP grades. |
| Ti-3Al-2.5V | Gr9 · UNS R56320 | 4.43 | Common for hydraulic and heat-exchanger tube; treated as 4.43. |
| Reference: 316L stainless | A2 / A4 family | 8.00 | Titanium is about 45 % lighter at the same volume. |
| Reference: 6061-T6 aluminium | AlMgSi1 | 2.70 | Lighter, but titanium carries roughly 3x the load per volume at temperature. |
Where this differs from the weighed ticket
- Plate runs positive on thickness. ASTM B265 allows plus tolerance on rolled plate, so 2.0 mm nominal often weighs like 2.15–2.30 mm. Order by nominal, invoice by actual.
- Bar is machined or peeled. Turned bar sits at or above nominal diameter; peeled forgings can run under. Density is the smaller error here.
- Tube wall varies along the length. Drawn tube has tolerance bands on both OD and wall — a 6 m length is a range, not a number.
- Cut pieces lose material. A 1000 x 2000 blank sawn from plate carries the kerf, roughly 3–4 mm on plasma and near zero on waterjet. Offcut is charged, not refunded, unless negotiated otherwise.
Using this before you order
Send the calculator output with your drawing. Mass tells us which mill route fits: one 40 kg plate blank is a cutting-shop job off stock; a 400 kg stack of the same size is a rolled-to-order campaign with different lead time and a very different price per kilo. Same part number, two different quotations — mass is usually what decides which one you get.
For customs paperwork and freight booking we issue weighed actuals per piece on the packing list. If your destination requires net-weight invoicing, say so at RFQ stage — it changes the document set, not the price.
Quick reference: CP titanium mass per m2
| Thickness | kg / m2 | 1000×2000 | 1250×2500 | 1500×3000 |
|---|---|---|---|---|
| 0.5 mm | 2.255 | 4.51 | 7.047 | 10.147 |
| 1 mm | 4.51 | 9.02 | 14.094 | 20.295 |
| 2 mm | 9.02 | 18.04 | 28.188 | 40.59 |
| 3 mm | 13.53 | 27.06 | 42.281 | 60.885 |
| 4 mm | 18.04 | 36.08 | 56.375 | 81.18 |
| 5 mm | 22.55 | 45.1 | 70.469 | 101.475 |
| 6 mm | 27.06 | 54.12 | 84.562 | 121.77 |
| 8 mm | 36.08 | 72.16 | 112.75 | 162.36 |
| 10 mm | 45.1 | 90.2 | 140.937 | 202.95 |
| 12 mm | 54.12 | 108.24 | 169.125 | 243.54 |
| 15 mm | 67.65 | 135.3 | 211.406 | 304.425 |
| 20 mm | 90.2 | 180.4 | 281.875 | 405.9 |
Questions this page settles
FAQ
Will I be invoiced for the calculator weight?
No. It is theoretical mass from nominal dimensions. Mills ship plate at positive thickness tolerance, so actual weighed weight on the packing list is usually a few percent higher. We quote and invoice weighed actuals; the calculator is for planning.
Which density for Grade 5?
4.43 g/cm3 for Ti-6Al-4V. Selecting Gr5 in the grade field applies it automatically.
Can you cut to my exact size instead of standard sheets?
Yes — sawing, waterjet and laser are all available. Odd sizes usually cost less cut from a standard sheet with a nesting plan than made to a rolled-to-order size. Send the drawing with the calculation and we will tell you which route is cheaper.
Does surface finish or condition change the weight?
No. Annealed versus mill finished affects machinability, flatness and residual stress, not density. Specify condition on the RFQ — annealed plate ships flat, hard-rolled does not.