EN 10204 3.1 vs 3.2: what to put on a titanium purchase order
A certificate type is not a material standard. Mixing the two up is one of the most common reasons a titanium shipment arrives with documents the receiving inspection team will not accept. Here is the distinction and the wording to use.
What EN 10204 actually defines
EN 10204 defines the type of inspection document that accompanies metallic products. It does not define the alloy, dimensions or mechanical properties. Those come from the material standard: ASTM B265 for plate and sheet, B348 for bar and billet, B338 for seamless and welded tube, the ASME SB equivalents, or DIN/EN and GB/T designations used by European and Asian mills.
Every purchase order therefore needs both parts: a material standard with its revision, and a document type. Asking only for "MTC" leaves the second part open to interpretation.
Type 3.1 — the normal industrial choice
- Issued by the manufacturer, signed by an authorised representative who is independent of the production department.
- Reports the results of specific tests on the heat or lot actually shipped — typically chemical composition and tensile properties, plus any supplementary tests agreed in the order.
- Traceable to a heat or lot number that must also appear on the material marking and the packing list.
- No third party countersigns it. This is what most buyers mean by a "mill test certificate" or "3.1 MTC".
For commercial titanium plate, bar, tube and forgings, 3.1 is the default and is sufficient for the large majority of receiving inspections.
Type 3.2 — when an independent inspector signs
- The mill performs the same tests, but the document is validated and signed by an independent inspection body or by the purchaser's nominated representative.
- Usually required by pressure-equipment codes, nuclear or aerospace programmes, or an EPC end user's project specification — not by the material itself.
- Adds an inspection visit, a lead-time buffer and a fee. Agree who books and pays for the inspector before the order is confirmed.
- A 3.2 certificate cannot be produced retrospectively from a 3.1 document. If 3.2 is required, it must be stated on the PO before production starts.
Other document types you may be offered
| Document | What it certifies | Typical fit for titanium |
|---|---|---|
| 2.1 | Declaration of compliance with the order, no test results | Rarely accepted for critical supply |
| 2.2 | Test report based on non-specific inspection | Non-critical stock items only |
| 3.1 | Specific heat/lot test results, manufacturer signed | Standard for plate, bar, tube, forgings |
| 3.2 | 3.1 results countersigned by an independent inspector | Code work, EPC project specifications |
Supplementary documents are separate from the certificate type: ultrasonic or penetrant testing reports, hydrostatic test results for tube, hardness or grain size, positive material identification, and any project-specific NACE or ISO 15156 requirements. List them individually rather than assuming they are included.
A PO line that works
Combine material standard, grade, product form, dimensions, document type and traceability in one line:
Titanium plate, ASTM B265 Gr 2, 6.0 × 1000 × 2000 mm, annealed, pickled; EN 10204 type 3.1 inspection certificate with chemical composition and tensile test results; heat number traceable on material marking and packing list.
For a 3.2 order, add: third-party inspection and countersignature required, inspector to be nominated before production release.
What to check when the documents arrive
- Heat or lot number matches across the certificate, the material marking and the packing list.
- Material standard and revision match the PO exactly (ASTM B265 vs ASME SB 265 is a real difference on code work).
- Test results are within the specified limits and the units are stated.
- The document carries the manufacturer's authorised signature or stamp and a date; a 3.2 also carries the independent inspector's validation.
Frequently asked questions
Can a 3.1 certificate be upgraded to 3.2 after the material has shipped?
No. The independent inspector has to witness or validate the testing and the link between the document and the specific lot. Order 3.2 from the start if the project needs it.
Is an ASTM certificate the same thing as an EN 10204 3.1 certificate?
No. ASTM B265 and its equivalents specify the material; EN 10204 specifies the inspection document that reports on it. A well-written order asks for both.
Do heat exchanger tubes always need 3.2 certification?
Only when the applicable code or the end user's project specification calls for it. Many commercial ASTM B338 tube orders are supplied with 3.1 plus hydrostatic and NDT reports.
Related reading: titanium standards explained · titanium RFQ checklist on our sister site · request a quotation.